MIRA Safety Gas Mask Microphone : Peltor and Ops-Core headset compatible For Sale

MIRA Safety Gas Mask Microphone : Peltor and Ops-Core headset compatible


Buy Now

MIRA Safety Gas Mask Microphone : Peltor and Ops-Core headset compatible:
$115.00

MIRA Safety Gas Mask Microphones compatible with CM-6M, CM-7M, CM-8M, & TAPR. This is for the microphone only.


Get crystal clear communication in any environment with the MIRA Safety Gas Mask Microphone. It’s engineered to replace the existing exhalation valve cover of your MIRA Safety gas mask, an upgrade that can be installed in seconds without tools. This 2-pin microphone offers integrated noise-canceling functionality with no additional power needed.  


KEY BENEFITS OF MIRA SAFETY GAS MASK MICROPHONE

Noise-canceling, dynamic, moving-coil microphone in a tough polymer housing

2-pin NEXUS U-173/U connector for compatibility with Peltor and Ops-Core headsets

Replaces your existing gas mask exhalation valve cover for quick and easy installation (no expert installation needed)

Heavy-duty polymer construction with durable retaining ring

Serviceable, with parts available in case of damage

Optimized for all-weather use (-33°C to +77°C) in any environment

Pivoting cable allows for easy amofferextrous alignment

Engineered to meet MIL-STD-461G and MIL-STD-810G

Provides an average of over 30,000 hours of use

IP67-rated for protection against dust, water, and oil

Can be fully submerged in up to 3 feet of water for ½ hour (not recommended)

Weighs less than two ounces (2 oz.), including the cable

Made in the Czech Republic

MIRA Safety gas masks come with enhanced speech diaphragms that allow for improved communication over shorter distances. But talking through a gas mask is never easy. Especially if you’re not right next to each other or you’re dealing with any noise, weather, or other distractions.

The MIRA Safety Gas Mask Microphone is cross-compatible with all adult-sized MIRA Safety gas masks, making it easy to swap between masks for different types of missions.


Installation takes just a few seconds, and you’re ready to connect to your existing communication system. Just like a standard headset, the microphone requires no additional power, and it has an average life expectancy of 30,000 hours.


Gas mask microphones are a relatively minor upgrade that can make a massive difference while using your mask. Communicating via hand signals is difficult in the best situation, and it’s impossible if you’re holding a rifle or riot shield. Having the ability to plug into your existing comms helps you stay better informed and make better decisions when they matter most.


GAS MASK MICROPHONE TECHNICAL DATA:

Electro-Acoustic Data

Type:Noise cancelling, Dynamic, Moving Coil

Output Impedance (1kHz):150Ω ± 10%

Real Output Level (at usual voice level):3.5mV rms ± 10%

Harmonic Distortion:max. 5% over a bandwidth of 315 Hz to 4000 Hz

Frequency Response (94 dB SPL, 1/1 octave bands):500 Hz-5 ± 3 dB

1000 HzReference

2000 Hz0 ± 3 dB

4000 Hz2 ± 3 dB

 


Environmental & Other Data

Weight (including cable):50g ± 10%

Cable Connector Type:NEXUS U-173/U

Cable Connector Pinout:1 - Microphone Signal (MIC +)

2 - Microphone Signal (MIC -)

Cable Length:400mm 150Ω ± 5%

Cable Strength:20 N / 20 S

Operating Temperature:(-33 to +71) °C

CE Certification:

Approved according to PPE directive 89/686/EEC and EMC directive 89/336/EEC

EMC / EMI:Designed in accordance with MIL-STD-461G

CBRN:Designed in accordance with ČSN EN 140

Ingress Protection (IEC standard 60529):IP67

Flame Retardant Properties (UL 94):min. level V2

Mean Time Between Failures (MTBF):>30,000 hours


IMPORTANT NOTE: This gas mask microphone is ONLY compatible with MIRA Safety respirators. This includes the CM-6M, CM-7M, CM-8M, and the TAPR.


STORAGE: The gas mask microphone is designed to be stored with your CM-6M or CM-7M gas mask. See storage guidance for those masks.

QUESTIONS & ANSWERS

The product description states that the microphone body is made out of \"heavy-duty polymer construction.\" Can you tell me the exact plastic that you guys are using?


The Microphone\'s body is made of polyamide, and the exhalation cap is made of a mixture of polyphenylene oxide and styrene (the mic is embedded into a standard exhalation cap, similar to what you\'d find on a stock mask).


The Microphone\'s body is made of polyamide, and the exhalation cap is made of a mixture of polyphenylene oxide and styrene (the mic is embedded into a standard exhalation cap, similar to what you\'d find on a stock mask).


Please contact me with any questions and Happy offerding!!! Will ship 1st class USPS.



Buy Now

Related Items:

MIRA Safety CM-7M Military Gas Mask w/ Drinking System MED Free Mira P3 Filter picture

MIRA Safety CM-7M Military Gas Mask w/ Drinking System MED Free Mira P3 Filter

$249.99



ONYX 45  Blower Motor With Connecting Tube Fits SGE MIRA SAFETY M40 M50 picture

ONYX 45 Blower Motor With Connecting Tube Fits SGE MIRA SAFETY M40 M50

$34.99



SUPERGUM Backup Battery Pack for ONYX90 PAPR picture

SUPERGUM Backup Battery Pack for ONYX90 PAPR

$37.00



Powered by WordPress. Designed by WooThemes